Since your tandem axle trailer has a 7K GVWR this means that you have 3.5K axles that use the following parts:
Inner Bearing - # L68149
Inner Race - # L68111
Outer Bearing - # L44649
Outer Race - # L44610
Grease Seal - # 58846 (1.719" inner diameter)
EZ Lube Grease Caps - # RG04-040
The bearings, races, and seals can be found in this kit # BK2-100, so all you'd need are the grease caps # RG04-040 to round out everything you need. Be sure to check what you currently have because even... view full answer...
If the TruRyde Bearing Kit with Grease Cap # DL21792 that you referenced uses the correct matching bearing set for your trailer (two of # L44643) then the included matching seal may fit. All components are matched for the BT8 spindle. This seal, # 34823, is a compatible cross-reference for the Transcom 12192. Its inner diameter is 1.249 inches and is outer diameter is 1.983 inches. You can measure your hub's inner bore to determine if this seal's outer diameter matches. view full answer...
It sounds like you're looking for the Bearing Kit with Grease Cap for 1" BT8 Spindles part # DL21792 which comes with two bearings, two races, a grease seal, cotter pin, and grease cap. It has everything you need for one side of an axle. It doesn't however come with a castle nut so for that you'd need the Trailer Spindle Nut 1" part # 165686. view full answer...
I was able to find everything you need for your 12,000 lb Dexter axles; the electric brakes, oil cap kit, oil seal, bearings, and races. I verified with Dexter that these are indeed the correct parts for your 12k axles. I'll go ahead and list out each of the parts you need to make it easier to order:
- Electric Trailer Brake with Dust Shield - Self-Adjusting - 12-1/4" - Left Hand - 12,000 lbs # AKEBRK-12L
- Electric Trailer Brake with Dust Shield - Self-Adjusting - 12-1/4" - Right Hand... view full answer...
The Kodiak Disc Brake Kit, part # K2HR712, that you referenced will fit axles that are rated for 7,000 lbs that use a #42 spindle. It will work with 16 inch and larger wheels that use an 8 on 6-1/2 bolt pattern. Since axles can vary depending on the manufacturer, as long as your current spindle is a #42 and/or uses the correct bearing, races, and seals, then these disc brakes will be the perfect upgrade for you. The correct bearings, races, and seals are as follows:
Bearings (sold separately)
Inner... view full answer...
We do indeed have the correct replacement bearings, grease seal, grease cap, and grease for your Malone MicroSport Trailer # MPG460G. What you will need is the following:
- Bearing Kit # BK1-100
- Grease Cap # F001518
- LubriPlate Poly HP-2 Wheel Bearing Grease # L11465
The bearing kit comes with the correct bearings, races, and seal for one hub on your MicroSport trailer. Then for a grease gun and bearing packer use the LubriMatic Grease Gun # L30200 and Bearing Packer # ALL647646. view full answer...
The Bearing Kit # BK2-100 is the one most likely to fit your Barrett trailer. You will want to confirm this is the correct kit by comparing it with your current bearings or measuring your spindle and hub. This will include a grease seal if you are planning to change to a greased hub.
Outer Bearing: # L44649 ID-1.063"
Outer Race: # L44610 OD-1.980"
Inner Bearing: # L68149 ID-1.378"
Inner Race: # L68111 OD-2.361"
Grease Seal: # RG06-050 ID-1.719", OD-2.565"
The Kodiak XL ProLube Kit #... view full answer...
I spoke with EZLoader, who gave me your bearing sizes.
The inner bearing is # LM48548, which measures 1.375 inches. Its matching race is # LM48510.
The outer bearing is # L44649, which measures 1.063 inches. Its matching race is # L44610.
You can also purchase a grease seal set, # BB60002. We also offer grease caps for 1.98 inch hub bores, such as the standard grease cap # RG04-020, and the EZ Lube grease cap # DC200L-DCRP.
I've attached several review videos of these products for... view full answer...
Thank you for the pictures and information of your axle!
I called Dexter and your Dexter P12 SLR axle with Serial Number D-423-4057 has a 9000lb axle rating, and uses an 8 on 6-1/2 hub and drum assembly with 5/8" studs like you mentioned.
For replacement bearings there is not a kit that has all of the bearings and races but you can purchase them all separately as follows:
Inner Bearing # 387A
Inner Race # 382A
Outer Bearing # 25580
Outer Race # 25520
Oil Seal # 10-51
And Oil Cap Kit... view full answer...
The Dexter Trailer Idler Hub Assembly, Item # 8-287-14UC1, has 9/16 inch studs. It works with 8,000-lb axles. The kit includes inner bearing (25580) and race, outer bearing and race (02475), race, oil seal, cap, wheel bolts, and lug nuts. It fits a 8 on 6-1/2 inch bolt pattern. view full answer...
I did a little research and found that the National Seal, 442109, has an inner diameter of 2.25 inches and an outer diameter of 3.376 inches. We carry two seals that can be used as a replacement for this seal. If your hubs have greased bearings you should use the TruRyde Grease Seal, item # GS-2250DL, or the TruRyde Grease Seals, item # RG06-070 (pair), which is a double lip seal and if your hubs have oil bath bearings, use Oil seal # 10-63.
Your inner bearing should match up with the... view full answer...
The Kodiak Disc Brake Kit part # K2HR35DS will work to replace a UFP DB-35 Hub/Rotor if you change out the seal to the Double Lip Seal for 3,700-lb Marine Hubs part # 168255TB. The races won't be an issue since they are specific to the hub. view full answer...
Yes, the CE Smith Trailer Idler Hub Assembly # CE13511 is compatible with the spindles on your Trailstar boat trailer since it uses the same bearings # L68149 and # L44649. It will fit your wheels with the 5-on-4-1/2 bolt pattern.
This spare hub kit includes the pre-greased hub along with bearings, races, grease seal, grease cap, lug nuts, and cotter pin (all in a handy case) so it makes for a perfect item to carry along with you, just in case. This hub is rated for use on 3500-lb axles.... view full answer...
If you are only in need of the oil seal we have the Kodiak # XLPROLUBE1980SEAL. If you are swapping your hubs over to use oil versus grease we do have the Kodiak Kit # XLPROLUBE1980KIT which will provide you with 2 seals for the axle, lube and oil caps to replace the grease cap. You may also want to order the Bearings # L68149, # L44649 and Races # L68111, # L44610 as it is very difficult to get all the grease out from inside the bearings.
If you are sticking with grease lubrication you... view full answer...
If you do not need electric brakes on your axle, I recommend the Dexter Trailer Hub Assembly # 42865-KIT. This assembly includes the # 25580 inner bearing, the # 14125A outer bearing, and a grease seal with a 2-1/4 inch inner diameter needed for the spindle on your existing axle.
Also included with the assembly are the races, grease cap, wheel bolts, and lug nuts. The hub has a 8 on 6-1/2 wheel bolt pattern. One hub assembly is included for the part number. You would want 2 of the # 42865-KIT... view full answer...
To determine the correct hub to replace the existing hub on your horse trailer I will need the inner and outer bearing numbers and the seal part numbers to select the proper parts for your spindle. The 8-256 number that you see on your hub is a casting number and even if I could match it to a Dexter hub assembly it would most likely not match up with the correct bearings. Remove a hub and you should find the part numbers on the back side of the bearings and the seal.
You will need to... view full answer...
Given the information you've provided the best option is going to be the Dexter Trailer Idler Hub Assembly for 2,200-lb Axles - 5 on 4-1/2 - Galvanized # 8-258-50UC1. This hub is going to come with the inner bearing # L44649 and race, outer bearing # L44649 and race, grease seal, grease cap, and galvanized lug nuts included so that you won't have to purchase them separately. The only thing you'll need to purchase separately is some marine grease # L74FR to pack your bearings and lube the... view full answer...
Yes it will!
Trailer Hub and Drum Assembly # 8-201-5 is a fit if you have inner bearing # 25580, outer bearing # LM67048 and grease seal 10-10, which is part # RG06-090. That grease seal is for EZ Lube axles so the correct grease cap would be # RG04-080.
Those parts do not come with this assembly, you would need to get them separately. For races you need # 25520 for the inner bearing and # LM67010 for the outer bearing.
This hub and drum is rated for 5,200 lbs and has a 6 on 5-1/2"... view full answer...
The Dexter 8-248 is a 3,500 lbs idler hub which uses the # L44649 outer # L68149 inner bearing and a 10-19 grease seal. For bearings/races/seals, you'd need the Hub Bearing Kit for Lippert, Dexter, and Al-Ko Axles - 3,500 lb with #84 Spindle item # BK2-100.
If you need replacement dust caps, use item # RG04-020 for a standard spindle (sold in pairs) or item # DC200L-DCRP for an E-Z Lube spindle which is sold individually. view full answer...
We do have a hub with a 4 on 4" bolt pattern with both inner and outer bearings # L44649, which is the Trailer Idler Hub Assembly for 2,000-lb Axles - Pre-Greased # AKIHUB-440-2-2K.
This hub does come with the bearings, races, grease seal, and grease cap. The cost can be found on the product page, and I have added a link below to a video review for you to check out as well. view full answer...
Go To Results